Quarter-turn Scotch yoke
Hydraulic or pneumatic. Double-acting or spring-return fail-safe. Up to 16,350 Nm.
HYLINE-R turns ball, plug and butterfly valves with a balanced Scotch yoke torque curve, strongest at the ends of the stroke where valves break away and reseat. Six sizes, each double-acting or spring-return, with ISO 5211 and NAMUR interfaces for the mounting and controls your valve needs.

16,350Nm
Peak double-acting torqueAt the stroke ends on the largest size, 4 bar air.
6sizes
Double-acting or spring-returnEach spring-return size comes fail-closed or fail-open.
2supplies
Hydraulic or pneumaticOr self-contained hydraulic with HYFLOW.
IP67
Ingress protectionO-ring sealed against dust and water.
Overview
A Scotch yoke turns the straight push of a piston into a quarter turn through a slotted yoke. The lever arm is longest at each end of the stroke, so the torque curve is U-shaped: highest at 0° and 90°, where a seated valve needs the most effort to break away and to reseat, and lower through mid-stroke, where the valve moves freely.
HYLINE-R puts that mechanism in a compact, modular package. Choose a hydraulic or pneumatic supply, then double-acting or spring-return, in six sizes. Springs sit in a sealed cartridge, a low-friction slider block spreads the contact loads across the yoke, and standard interfaces take the mounting kits, switchboxes and positioners your valve needs.
Our established ranges already cover the vast majority of quarter-turn duties. Where yours is genuinely different, we engineer the mounting, controls or package around it.
At a glance
Balanced torque
The symmetrical yoke gives the same U-shaped curve in both directions: most torque at each end of the stroke, where the valve breaks away and reseats, and less through mid-stroke, where it moves freely. Every size follows the same shape, up to 16,350 Nm.
Advantages
Every HYLINE-R is built around a symmetrical yoke housing. A cylinder sits on one side, and on the other either a second cylinder for double-acting units or a sealed spring cartridge for spring-return units.

Peak output at both ends of the 90° stroke, matching the way quarter-turn valves load an actuator at breakaway and reseating.
Springs are fully contained in a sealed cartridge, so installation, removal and maintenance are safer.
Keeps the actuator envelope and weight down while holding the torque needed for dependable fail-safe operation.
Spreads contact loads across the yoke, reducing localised stress and wear over repeated cycles for a longer cycle life.
O-ring seals protect the internal parts against dust and water ingress in exposed and demanding sites.
Externally accessible stops set precise open and closed positions, for reliable shut-off without unnecessary load on the valve seat.
Standard NAMUR interfaces simplify fitting switchboxes, positioners and other control accessories.
On pneumatic units, internal tie rods hold cylinder alignment and take the operating loads, helping prevent uneven piston and seal wear.
On hydraulic units, a compact cylinder gives substantial torque from a smaller envelope, where space is tight.
Technical data
Six sizes, each double-acting or spring-return. Pneumatic torque figures are from the HYLINE-R pneumatic data sheet, with a 4 bar air supply.

| Property | HYLINE-R |
|---|---|
| Type | Quarter-turn Scotch yoke actuator, 90° rotation |
| Supply | Pneumatic (compressed air) or hydraulic |
| Double-acting | Powered in both directions, fail-fixed on loss of supply |
| Spring-return | Powered one way, spring return to a fail-closed or fail-open position |
| Sizes | Six, across frames T1, T2, T4 and T5 (model codes below) |
| Pneumatic rating basis | 4 bar air supply |
| Ingress protection | IP67, O-ring seals |
| Valve mounting | ISO 5211 compatible, with custom mounting kits available |
| Accessory mounting | NAMUR interfaces for switchboxes, positioners and other controls |
| Travel stops | Externally accessible and adjustable, open and closed |
| Position indicator | Mechanical indicator, optional |
| Pneumatic hardware | Solenoid valves, filter regulator and quick exhaust valves supplied where required |
| Hydraulic option | Integrated HYFLOW unit for a self-contained package |
Air operated in both directions. Torque at 4 bar.
| Model | Action | 0° Nm | 45° Nm | 90° Nm |
|---|---|---|---|---|
| E-R-T1-S-201DA | Double-acting, fail-fixed | 1,300 | 700 | 1,300 |
| E-R-T1-S-251DA | Double-acting, fail-fixed | 2,050 | 1,100 | 2,050 |
| E-R-T2-S-301DA | Double-acting, fail-fixed | 3,750 | 2,050 | 3,750 |
| E-R-T4-S-401DA | Double-acting, fail-fixed | 9,350 | 5,050 | 9,350 |
| E-R-T4-S-451DA | Double-acting, fail-fixed | 11,900 | 6,400 | 11,900 |
| E-R-T5-S-451DA | Double-acting, fail-fixed | 16,350 | 8,800 | 16,350 |
Air operated one way with spring return. Spring torque is given at the fail position. Net torque is the air torque at 0°, 45° and 90° with a 4 bar supply, less the opposing spring torque.
| Model | Fail position | Spring Nm at fail position | Net 0° Nm | Net 45° Nm | Net 90° Nm |
|---|---|---|---|---|---|
| E-R-T1-S-201SRC4 | Fail-closed | 500 | 822 | 358 | 501 |
| E-R-T1-S-201SRO4 | Fail-open | 500 | 501 | 358 | 822 |
| E-R-T1-S-251SRC4 | Fail-closed | 626 | 1,463 | 682 | 1,061 |
| E-R-T1-S-251SRO4 | Fail-open | 626 | 1,061 | 682 | 1,463 |
| E-R-T2-S-301SRC5 | Fail-closed | 1,485 | 2,304 | 989 | 1,351 |
| E-R-T2-S-301SRO5 | Fail-open | 1,485 | 1,351 | 989 | 2,304 |
| E-R-T4-S-401SRC4 | Fail-closed | 3,546 | 3,193 | 1,102 | 911 |
| E-R-T4-S-401SRO4 | Fail-open | 3,546 | 911 | 1,102 | 3,193 |
| E-R-T4-S-451SRC4 | Fail-closed | 4,432 | 7,480 | 3,271 | 4,627 |
| E-R-T4-S-451SRO4 | Fail-open | 4,432 | 4,627 | 3,271 | 7,480 |
| E-R-T5-S-451SRC4 | Fail-closed | 6,192 | 10,178 | 4,422 | 6,191 |
| E-R-T5-S-451SRO4 | Fail-open | 6,192 | 6,191 | 4,422 | 10,178 |
Hydraulic HYLINE-R comes in the same six sizes, double-acting or spring-return, with model codes starting E-RH. Torque depends on your supply pressure: tell us the pressure and the valve torques and we will send the figures for your duty.
Source: HYLINE-R pneumatic data sheet, Advanced Actuators, October 2026 issue. Images are representative. The final model number, certification and configuration are confirmed when you order.
Control and feedback
NAMUR interfaces on every HYLINE-R take our own instrumentation, so the actuator, feedback and positioner can all come from one supplier.
Position transmitter, A-HR
High-resolution position feedback for on-off and modulating valves.
Positioner, A-HC and A-HCR
Closed-loop positioning for modulating duties on hydraulic and pneumatic actuators.
3D model
Rotate, zoom and explode a representative HYLINE-R to see how the yoke, slider block, cylinder and spring cartridge fit together, with notes on the key features.
The model is about 15 MB, so it only loads when you ask for it.
Valves and applications
HYLINE-R is built for quarter-turn isolation and control duties where dependable torque, fail-safe action and long service life matter.
Ball valvesPlug valvesButterfly valves
Hazardous area? Tell us the zone, gas group and temperature class, and we will confirm the certification for your exact unit.
Not sure it is the right fit? For smaller pneumatic valves, HYLINE-K rack and pinion may suit. With no air or hydraulic supply, see the HYLINE-E electric range.
Isolation and fail-safe duties on production, process and utility lines, onshore and offshore.
On-off and fail-safe isolation where a valve must reach a safe position on loss of supply.
Large quarter-turn valves at treatment works, pumping stations and on distribution networks.
Isolation duties on cooling water, fuel and auxiliary systems.
Compact, sealed units for exposed decks and space-limited skids.
Certification
Certification depends on the specification, the components used and the area classification. Tell us what your project calls for and we will confirm the marks for your unit when we quote.









Downloads
Sizing help
Send the valve type, size and torques, and we will come back with the right size and its torque at your supply.
Already installed
Overhaul, repair and spares for actuators in service, with commissioning support on site.
Size your HYLINE-R
We just need three details.
Replacing one? Send the model code from the nameplate and a photo, and we will work from those.
Type and size, with its breakaway, running and reseating torques if you have them.
Air or hydraulic, and the pressure. No supply? We will look at HYFLOW or HYLINE-E.
Double-acting or spring-return, the fail position, on-off or modulating, and the area classification.
Email us your detailsCall +44 (0)1535 655151
Prefer us to call you? Request a callback.
A quarter-turn actuator that converts the straight-line force of a piston into rotation through a slotted yoke. Its torque is highest at each end of the 90° stroke and lower in the middle, which suits the breakaway and reseating torques of ball, plug and butterfly valves.
A rack and pinion gives a broadly even torque through the stroke and is often chosen for smaller valves. A Scotch yoke gives more torque at the ends of the stroke, which suits larger, high-torque quarter-turn valves. We offer both: HYLINE-R Scotch yoke and HYLINE-K rack and pinion.
On a 4 bar air supply, double-acting models give 1,300 Nm to 16,350 Nm at the ends of the stroke and 700 Nm to 8,800 Nm at mid-stroke. On spring-return models the spring gives 500 Nm to 6,192 Nm at the fail position; the tables on this page list the net air torque for every model.
Yes. Spring-return models drive the valve to its safe position when supply is lost, fail-closed or fail-open, with the springs held in a sealed cartridge. Double-acting models are fail-fixed: they stay where they are.
Pneumatic suits sites with a constant supply of compressed air, and we supply the solenoid valves, filter regulator and quick exhaust valves where they are needed. Hydraulic gives high torque from a compact envelope, and with an integrated HYFLOW unit it needs no external hydraulic supply.
The valve interface is ISO 5211 compatible, and we supply custom mounting kits where a valve needs one. Send us the valve type, size and top-works details, or a drawing if you have one.
Yes. NAMUR interfaces take switchboxes, positioners and other control accessories. Our HYTRACK transmitter gives 4-20 mA position feedback with HART, and HYCONTROL adds closed-loop positioning for modulating duties.
Tell us the zone, gas group and temperature class, and we will confirm the certification for your exact unit before you order.