Home›Products›HYTRACK

Ex d position transmitter

HYTRACK Position Transmitters

Fast, high-resolution 4-20 mA position feedback for rotary actuators, with HART 7.

HYTRACK measures rotary position up to 360° with a 12-bit contactless sensor and reports it on a two-wire, loop-powered 4-20 mA signal. Limit switches, a mechanical indicator and HART are options, all in a flameproof 316L stainless steel housing.

Get a priceDownload the data sheet

Two HYTRACK position transmitters in 316L stainless steel housings, one with the optional mechanical indicator

12bit

Contactless sensorNo wear on the measuring element.

20ms

Output responseSampling every 150 μs.

360°

Rotary rangeEnd positions set in two steps.

IP66

Ingress protectionNEMA 4X, in 316L stainless steel.

Overview

Accurate feedback, simply set up

HYTRACK is our feedback transmitter. It delivers fast, high-resolution position data for most rotary actuators, from on-off valves to modulating duties, and suits harsh sites thanks to its rugged 316L enclosure.

It mounts on a NAMUR shaft with F05 and F08 ISO 5211 patterns. Magnetic buttons set it up through the closed lid, so the flameproof enclosure stays intact, and the display shows position in percent or milliamps.

HYTRACK comes fitted to our own actuators or as a standalone transmitter for other rotary actuators, and it is built into HYCONTROL A-HCR positioners.

Choose HYTRACK for

  • 4-20 mA feedback on rotary actuators, with or without HART
  • Open and closed confirmation from mechanical or proximity switches
  • Hazardous areas, with ATEX, UKEX, IECEx and INMETRO certificates
  • Offshore and corrosive sites that need 316L stainless steel

At a glance

HYTRACK

Type
Ex d position transmitter, A-HR
Output
4-20 mA, HART 7 option
Sensor
12-bit contactless
Range
0 to 360°
Switches
2 or 4, mechanical or proximity
Supply
4-20 mA, 24 V DC loop-powered
Housing
316L, IP66, NEMA 4X
Ambient
-40 °C to +70 °C

Set up in minutes

Two positions, then done

Calibration takes two steps: move the valve to one end and confirm, then the other. From the same menu you can reverse the signal or trim the 4 mA and 20 mA points, all with magnetic buttons through the closed lid.

HYTRACK position transmitter from the side, showing the cable entries and the drive shaft
HYTRACK from the side: cable entries in the base, and the drive shaft below.
  • Set position 1Move the valve to one end and press Enter
  • Set position 2Move it to the other end and press Enter
  • AdjustReverse the output or trim 4 mA and 20 mA if needed

Advantages

Why choose HYTRACK

A compact transmitter that keeps feedback accurate, wiring simple and the enclosure sealed.

Exploded view of a HYTRACK position transmitter, showing the lid, display and sensor assembly

Contactless sensing

A 12-bit sensor with no mechanical wear, for reliable, precise feedback over a long service life.

Fast response

Sampling every 150 μs for a 20 ms output response, with hysteresis below 0.048%.

Two-wire loop power

4-20 mA, 24 V DC, two-wire loop-powered.

HART 7

Digital communication for diagnostics, using a generic device description.

Sealed setup

Magnetic buttons configure the unit without opening the flameproof enclosure.

Clear display

A 128 x 64 pixel LCD shows position in percent or milliamps.

Limit switches

Two or four mechanical or proximity switches, NAMUR compatible where applicable.

Mechanical indicator

An optional visual indicator for rotary actuators, with custom options.

316L stainless steel

IP66 and NEMA 4X, for offshore and corrosive environments.

Technical data

HYTRACK technical specifications

Specifications from the HYTRACK data sheet. Each unit's configuration and certification are confirmed when you order.

General data

PropertyHYTRACK
TypeEx d 4-20 mA position transmitter, A-HR
Sensor12-bit contactless
Measuring rangeRotary, 0 to 360°, end positions set at calibration
Output4-20 mA, two-wire loop-powered; HART 7 digital option
Operating voltage24 V DC
Maximum load500 Ω
Sampling rate150 μs
Output response time20 ms
HysteresisBelow 0.048%
Limit switchesTwo or four; mechanical (standard) or proximity
DisplayLCD, 128 x 64 pixels
Housing316L stainless steel
Ingress protectionIP66 and NEMA 4X
Ambient temperature-40 °C to +70 °C
Storage temperature-40 °C to +100 °C
Cable entries3 x M20 x 1.5; option 3 x ½ inch NPT
MountingNAMUR shaft, F05 and F08 to ISO 5211
DimensionsØ150 mm x 135 mm
WeightApproximately 9 kg

Configurations

Model codes run from A-HR-S2M3, with two mechanical switches, to A-HR-FS4P3VM, with 4-20 mA, four proximity switches and an indicator. Other configurations are available on request.

FeedbackSwitch typeSwitchesMechanical indicator
Switches onlyMechanical or proximityTwo or fourOptional
4-20 mA and switchesMechanical or proximityTwo or fourOptional

HART

PropertyHYTRACK
Signal4-20 mA with HART digital
HART revision7
Universal commandsSupported
Device descriptionGeneric only; no specific DD needed

Hazardous-area certification

The certificates cover the A-H* flameproof enclosure used by HYTRACK, HYCONTROL and HYDRIVE.

SchemeCertificate and marking
ATEXExVeritas 22 ATEX 1354 X, issue 3
UKEXExVeritas 22 UKEX 1355 X, issue 3
IECExIECEx EXV 22.0040X, issue 3, February 2026
INMETROCPEx 24.1587 X
Gas markingII 2 G Ex db IIC T6 to T4 Gb
Dust markingII 2 D Ex tb IIIC T85 °C to T135 °C Db

Temperature class by maximum ambient

From the certificate schedules. The lowest ambient is -40 °C in every class.

Gas and dust classMaximum ambient
T6, T85 °C+50 °C
T5, T100 °C+70 °C
T4, T135 °C+105 °C, or +90 °C with a glass window lid

Sources: HYTRACK A-HR data sheet, October 2026, and installation manual, Advanced Actuators; ExVeritas ATEX and UKEX, IECEx and INMETRO certificates. Specifications vary with configuration; each unit is confirmed when you order.

Options

Configure your HYTRACK

Choose the feedback, the switches and the entries; the housing and sensor stay the same.

Feedback

Switches only, or 4-20 mA with switches; HART 7 as a digital option.

Switch type

Mechanical as standard, or non-contact proximity switches.

Switch quantity

Two or four switches.

Mechanical indicator

An optional visual position indicator for rotary actuators.

Cable entries

Three M20 x 1.5 entries, or three ½ inch NPT.

Custom builds

Other configurations are available on request.

3D model

Take a HYTRACK apart in 3D

Rotate, zoom and explode a representative HYTRACK to see the housing, sensor, display and shaft.

Load the 3D model

The model only loads when you ask for it.

Valves and applications

Where HYTRACK works

HYTRACK gives position feedback on quarter-turn valves, on our actuators and on other rotary actuators with NAMUR mounting.

Quarter-turn valvesChoke valvesRotary actuatorsNAMUR mounting

Need closed-loop control as well? HYCONTROL A-HCR has HYTRACK built in: see HYCONTROL positioners.

Hazardous area? Tell us the zone, gas group and temperature class, and we will confirm the certification for your exact unit.

  • Oil and gas

    Feedback on choke, control and isolation valves, onshore and offshore.

  • Hazardous areas

    Flameproof and dust-protected, to equipment protection levels Gb and Db.

  • Our actuators

    Fitted to HYSTEP, HYLINE and HYLINE-R, and to other rotary actuators with NAMUR mounting.

  • Upgrades

    Adds 4-20 mA and HART feedback to rotary actuators already in service.

Certification

Specified to suit your project

Certified for hazardous areas under ATEX, UKEX, IECEx and INMETRO, with the certificates listed in the technical data. Tell us what your project calls for and we will confirm the marks for your unit when we quote.

ISO 9001 certified quality managementISO 45001 certified health and safety managementEx mark for equipment for explosive atmospheresIECEx certification schemeUKCA markingINMETRO certification for BrazilIP66 ingress protection ratingIP68 ingress protection ratingNEMA 4X enclosure rating

Downloads

HYTRACK downloads

  • HYTRACK data sheet

    PDF, 1.6 MB. Specifications, HART, dimensions, markings and variants.

    Download

  • Controls and instrumentation flyer

    PDF, 1.6 MB. HYTRACK with the rest of our instrumentation.

    Download

  • Technical library

    Manuals, declarations and Ex certificates, on our document library.

    Download

Sizing help

Not sure which size?

Send the actuator make and mounting, the signals and switches you need, and the area classification, and we will confirm the model.

Already installed

Servicing and repairs

Overhaul, repair and spares for actuators in service, with commissioning support on site.

Size your HYTRACK

Looking for a HYTRACK or a price?

We just need three details.

Replacing one? Send the model code from the nameplate and a photo, and we will work from those.

  1. Actuator

    Make, model and mounting, or the Advanced Actuators range it will fit.

  2. Signals

    4-20 mA, HART, and how many limit switches.

  3. Site

    Area classification, cable entries and whether you need an indicator.

Email us your detailsCall +44 (0)1535 655151

Prefer us to call you? Request a callback.

FAQs

HYTRACK questions

Anything else? Call +44 (0)1535 655151 or email sales@advanced-actuators.com.

What does HYTRACK do?

It measures the rotary position of an actuator or valve and reports it as a 4-20 mA signal, with optional HART 7 and limit switches.

How is HYTRACK calibrated?

In two steps: set position 1 at one end of travel, then position 2 at the other, using the magnetic buttons. You can also reverse the output or trim the 4 mA and 20 mA points.

Does it need its own power supply?

No separate power supply is needed. HYTRACK is powered by its 4-20 mA, 24 V DC two-wire loop.

Which limit switches are available?

Two or four switches, mechanical as standard or non-contact proximity, with or without the 4-20 mA output.

Will it fit my actuator?

HYTRACK mounts on a NAMUR shaft with F05 and F08 ISO 5211 patterns. Send us the actuator details and we will confirm.

Which hazardous-area certificates does it hold?

ATEX 22 ATEX 1354 X, UKEX 22 UKEX 1355 X, IECEx EXV 22.0040X and INMETRO CPEx 24.1587 X, marked Ex db IIC Gb and Ex tb IIIC Db. The temperature class depends on the maximum ambient.

Is HART supported?

Yes, HART revision 7 as a digital option on the 4-20 mA output, using a generic device description.

Can HYTRACK be built into a positioner?

Yes. HYCONTROL A-HCR positioners have HYTRACK feedback built in. See HYCONTROL.

Back to top